當前位置：導致丁基膠涂布過程中產生氣泡的原因
時間：2018-05-10 來源：http://www.lingmaicnc.com/ 發布人：昌盛機械
膠缸中丁基膠沒有排凈即更換加入新的丁基膠。雙組份打膠機如果在膠缸中存在丁基膠的情況下退出活塞，具有優良粘接性的丁基膠。
If the butyl rubber is not discharged, the new butyl rubber is replaced. If there is butyl rubber in the rubber cylinder, the piston will have good adhesive properties.
在膠缸底部和活塞上會形成山峰狀，而在推人新的丁基膠后，膠缸和活塞粘接的山峰狀丁基膠與新的丁基膠之間會存在大量氣泡，區別只不過是活塞處氣泡比膠缸底部氣泡少一些。因此在涂膠過程中表現為剛剛換膠后氣泡較大，毛刺較多，而在將近結束時，氣泡較少的現象。
At the bottom of the cylinder and the piston, the peak is formed, and after the new butyl rubber is pushed, there will be a large number of bubbles between the gums and the new butyl rubber. The difference is only that the bubbles at the piston are less than the bubbles at the bottom of the cylinder. Therefore, during the process of gelatinization, the bubbles are bigger and the burrs are more after just changing the glue, and the bubbles are less at the end.
成品丁基膠內部存在氣泡。因丁基膠為半固體粘稠狀不干膠，在生產過程中如果混入氣泡不加以處理或處理不徹底而把氣泡存留在膠體中，在涂布過程中氣泡可隨膠體從涂膠頭排出從而影響涂布質量。
There are bubbles inside the finished butyl rubber. Because butyl rubber is a semi solid sticky adhesive, the bubble can be retained in the colloid in the process of production. In the process of coating, the bubble can be discharged with the colloid from the gel head and influence the coating quality.
膠缸和膠頭溫度過高。由于丁基膠內部存在大分子有機物質，如果溫度過高，有機物質會發生裂解，產生小分子物質，其中一些在高溫下以氣態形式存在，如果此時丁基膠涂布操作，排出膠頭后，即高溫高壓狀態下的氣體突然降壓，其體積會迅速膨脹，產生大量微氣泡，使膠條表現為毛刺現象。
The temperature of the rubber cylinder and the rubber head is too high. Due to the existence of large molecular organic matter in the butyl rubber, if the temperature is too high, the organic matter will break up and produce small molecules. Some of them exist in the form of gaseous state at high temperature. If the adhesive is coated at this time, the gas will suddenly depressurization at high temperature and high pressure, and the volume will expand rapidly. The bulge produces a large number of micro bubbles, which makes the rubber strip show burr phenomenon.
丁基膠體直徑與膠缸直徑相差太大。如果丁基膠直徑大大小于膠缸直徑，丁基膠與膠缸內壁存在較大空間并充斥著大量空氣，丁基膠在活塞強大的機械力擠壓下，膠體外壁不規則向外膨脹
There is too much difference between the diameter of the butyl colloid and the diameter of the cylinder. If the diameter of the butyl rubber is much smaller than the diameter of the cylinder, the inner wall of the butyl rubber and the inner wall of the cylinder is filled with a large amount of air. Under the powerful mechanical force extrusion of the butyl rubber, the outer wall of the colloid outer wall expands outwards.
把部分空氣擠壓封閉在膠體與缸壁之間'雖然在擠壓過程中會有部分空氣從活塞與缸壁之間的縫隙中排出，但被封閉的空氣由于丁基膠的阻礙，不能排出，導致在丁基膠涂布過程中間隔一定時間就會有氣泡產生。
Part of the air is squeezed between the colloid and the cylinder wall, although part of the air is discharged from the gap between the piston and the cylinder wall during the extrusion process, but the closed air can not be expelled because of the butyl rubber.
本公司以可靠的質量，完美的服務，合理的價格贏得了新老客戶的信賴。在充滿挑戰和機遇的世紀里，我們將銳意進取，契而不舍地追求精益求精的品質和至善至美的服務。希望我們將有為您服務的榮幸!
Our company has won the trust of new and old customers with reliable quality, perfect service and reasonable price. In the century of challenges and opportunities, we will strive for the best quality and the best service. I hope we will have the honor of serving you!
- 丁基膠涂布機液壓油的選擇指南 2025/10/31
- 玻璃涂布機設備操作流程 2025/10/30
- 雙組份打膠機比例怎么調 2025/10/29
- 全自動鋁條折彎機折彎角度偏差的解決方法 2025/10/29
- 中空玻璃丁基膠涂布機漏油怎么解決 2025/10/28
- 臥式丁基膠涂布機糾偏原理 2025/10/27
- 立式丁基膠涂布機故障維修 2025/10/25
- 全自動丁基膠涂布機怎么換膠 2025/10/24
- 丁基膠涂布機液壓系統油路原理 2025/10/23
- 全自動中空玻璃封膠線的設備特點 2025/10/22
產品分類Product categories
聯系我們Contact us
- 咨詢熱線：0531-85717458 13705446998
- 公司地址： 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們：
