當前位置：雙組份打膠機的使用注意事項
時間：2019-04-08 來源：http://www.lingmaicnc.com/ 發布人：昌盛機械
雙組份打膠機的出現，給中空玻璃生產行業帶來一股新的生機和活力。但是人無完人，機器也當然是如此，那么我們在使用中要注意哪些事項呢？我們接下來一起看看！
The emergence of two-component gluing machine has brought a new vigor and vitality to the hollow glass production industry. But no one is perfect, and so is the machine, so what should we pay attention to in the use? Let's take a look next!
1.由于雙組份密封膠的固化需求一定時間，因而，已涂了雙組份密封膠的玻璃應程度悄悄搬動。
1. Because of the curing time of the two-component sealant, the glass coated with the two-component sealant should be moved quietly.
2.A組、B組份膠應堅持清潔，嚴防異物進入膠中。
2. Group A and B glue should be kept clean and foreign bodies should be strictly prevented from entering the glue.
3.在連續工作過程中，膠槍每次中止工作時間普通不得超越20分鐘，否則，應用A組份膠沖出全部混合膠，直至單一的A組份膠從槍口排出為止。
3. In the continuous working process, the rubber gun should not stop working for more than 20 minutes at a time. Otherwise, the rubber of component A should be used to punch out all the mixtures until a single component A is discharged from the muzzle of the gun.
4.高壓膠管不得強行擠壓、彎曲，避免影響系統正常工作。
4. High-pressure hose shall not be forced to extrude or bend to avoid affecting the normal operation of the system.
5.混膠器應經常堅持暢通，以保證良好的出膠效果。如遇梗塞狀況，可用丙酮浸泡后清洗。倡議每5組清洗一次。
5. Mixers should always be unblocked in order to ensure a good gumming effect. In case of infarction, it can be washed after soaking in acetone. It is advocated to clean every five groups.
6.當膠槍長時間不用時（超越一周），應拆下槍體運用溶劑將膠槍和混膠器內的殘留膠體清洗潔凈。
6. When the rubber gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the rubber gun and mixer should be cleaned by solvent.
7.不同雙組份膠消費廠家所消費的膠內含雜質數量不同，依據實踐狀況明晰B組分的過濾網及單向止回閥，倡議每兩組清洗一次。
7. The amount of impurities in the rubber consumed by different two-component rubber manufacturers is different. According to the practical situation, the filter screen and check valve of component B are clearly defined. It is suggested that each two groups be cleaned once.
8.任何因膠體固化所形成的膠槍、管路或整機的毛病，一概不在保修范圍之內。
8. Any defect of rubber gun, pipeline or whole machine caused by gel solidification is not covered by warranty.
9.定期給各泵的加油口加油，應保證油霧器內不時油。
9. Regular refueling at the refuelling port of each pump should ensure that the oil mist is oiled from time to time.
好了，今天的內容就給大家介紹到這里了，更多關于雙組份打膠機的精彩內容歡迎關注我們的官網：http://linshi.jncsjx.com
Well, today's content will be introduced to you here, more wonderful content about two-component glue machine welcome to pay attention to our official website: http://linshi.jncsjx.com
- 丁基膠涂布機液壓油的選擇指南 2025/10/31
- 玻璃涂布機設備操作流程 2025/10/30
- 雙組份打膠機比例怎么調 2025/10/29
- 全自動鋁條折彎機折彎角度偏差的解決方法 2025/10/29
- 中空玻璃丁基膠涂布機漏油怎么解決 2025/10/28
- 臥式丁基膠涂布機糾偏原理 2025/10/27
- 立式丁基膠涂布機故障維修 2025/10/25
- 全自動丁基膠涂布機怎么換膠 2025/10/24
- 丁基膠涂布機液壓系統油路原理 2025/10/23
- 全自動中空玻璃封膠線的設備特點 2025/10/22
產品分類Product categories
聯系我們Contact us
- 咨詢熱線：0531-85717458 13705446998
- 公司地址： 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們：
