當前位置：丁基膠涂布機升級設計的重要要素
時間：2024-08-19 來源：http://www.lingmaicnc.com/ 發布人：昌盛機械
亮點：
Highlights:
1、采用雙機油缸，配有大體積膠缸，可一次性裝載14L丁基膠（2塊正常的￠180mm的丁基膠）。
1. Adopting dual oil cylinders and equipped with large volume rubber cylinders, it can load 14L of butyl rubber (2 pieces of normal ￠ 180mm butyl rubber) at once.
2、增壓系統的主泵采用德國原裝進口麥格思維特（MAXIMATOK）的增壓泵。
2. The main pump of the boosting system adopts the German imported MAXIMATOK boosting pump.
主要性能特點:
Main performance characteristics:
1、該機為半自動涂布機（即人工扶持間隔框進行逐邊操作）,變頻調速。
1. This machine is a semi-automatic coating machine (i.e. manually supporting the interval frame for edge by edge operation), with variable frequency speed regulation.
2、將間隔框放在傳送帶上人工扶持框傳送帶運行，通過傳感器時，傳送壓輪及打膠閥按設定程序自動動作。
2. Place the spacer frame on the conveyor belt and manually support it to run. When passing through the sensor, the conveyor pressure wheel and glue valve will automatically operate according to the set program.
3、擺動氣缸動作、壓輪壓下，壓送鋁間隔框行進，當間隔框到達打膠頭時打膠，將膠均勻地涂在鋁間隔框上。
3. Swing the cylinder and press down the pressure wheel to push the aluminum spacer frame forward. When the spacer frame reaches the glue head, apply glue evenly to the aluminum spacer frame.
4、等間隔框另一側快要到達壓輪時，壓輪抬起，離開打膠頭時，膠閥自動關閉，停止打膠，以上程序由PC控制，時間有人機界面控制，可以觸摸調節。
4. When the other side of the equidistant box is about to reach the pressure wheel, the pressure wheel lifts up and leaves the glue head. The glue valve automatically closes and stops gluing. The above program is controlled by a PC, and the time is controlled by the human-machine interface, which can be adjusted by touch.
5、在設計、選用元氣件以及涂膠效果方面，在國內均屬水平。
5. In terms of design, selection of components, and coating effect, it is at the same level in China.
6、采用PC控制系統，定位、傳送、涂膠均自動完成。
6. Using a PC control system, positioning, conveying, and gluing are all automatically completed.
7、輸送采用變頻調速電機調速，運行速度平穩。
7. The conveyor adopts variable frequency speed control motor for speed regulation, and the running speed is stable.
8、有不泄壓即可自動調定位機構，充分保證涂膠膠頭與隔框兩側間距涂膠均勻。
8. There is an automatic positioning mechanism that can be adjusted without pressure relief, fully ensuring that the adhesive head and the distance between the two sides of the partition frame are evenly coated.
主要技術參數：
Main technical parameters:
擠膠壓力:12-14Mpa
Squeezing pressure: 12-14Mpa
電源:380V
Power supply: 380V
打膠溫度:100-140度
Glue temperature: 100-140 degrees Celsius
總功率: 2.5Kw
Total power: 2.5Kw
氣動壓力:0.5-0.8Mpa
Pneumatic pressure: 0.5-0.8Mpa
膠頭可調范圍:4-20mm
Adjustable range of adhesive head: 4-20mm
打膠速度:22米/分鐘
Glue application speed: 22 meters per minute
外形尺寸:3000*700*1236mm
Dimensions: 3000 * 700 * 1236mm
總重量:850kg
Total weight: 850kg
- 丁基膠涂布機液壓油的選擇指南 2025/10/31
- 玻璃涂布機設備操作流程 2025/10/30
- 雙組份打膠機比例怎么調 2025/10/29
- 全自動鋁條折彎機折彎角度偏差的解決方法 2025/10/29
- 中空玻璃丁基膠涂布機漏油怎么解決 2025/10/28
- 臥式丁基膠涂布機糾偏原理 2025/10/27
- 立式丁基膠涂布機故障維修 2025/10/25
- 全自動丁基膠涂布機怎么換膠 2025/10/24
- 丁基膠涂布機液壓系統油路原理 2025/10/23
- 全自動中空玻璃封膠線的設備特點 2025/10/22
產品分類Product categories
聯系我們Contact us
- 咨詢熱線：0531-85717458 13705446998
- 公司地址： 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們：
