當前位置：雙組份打膠機的工作流程
時間：2024-05-16 來源：http://www.lingmaicnc.com/ 發布人：昌盛機械
1、雙組份打膠機設備應安裝在干燥、無粉塵、無腐蝕性氣體的壞境中（該要求與其他設備一致，當然如果條件達不到至少爭取無腐蝕性氣體，畢竟設備中有電線以及管路這些配件抗腐蝕性不高）。
1. The two-component glue machine equipment should be installed in a dry, dust-free, and corrosion-free environment (this requirement is consistent with other equipment, but if the conditions are not met, at least strive for corrosion-free gas, after all, there are wires and pipelines in the equipment, and these accessories have low corrosion resistance).
2、最好在室內堅硬地面上，地面應水平度要好。
2. It is best to place it on a hard indoor floor with good levelness.
3、雙組份打膠機安裝之前，應先檢查是否有因運輸、搬動造成的變形、損壞和緊固件松動情況，之前就曾經有客戶在移動打膠機的過程中把設備的智能控制系統的一個零部件碰掉了而導致設備無法正常運行，我們的工作人員到現場后才排查出的原因。
3. Before installing the two-component glue machine, it is necessary to check for any deformation, damage, or loose fasteners caused by transportation or moving. Previously, a customer had accidentally knocked off a component of the intelligent control system of the equipment while moving the glue machine, causing it to malfunction. Our staff only found out the cause after arriving at the site.
4、首先我們可以根據地面平整度的實際情況來通過調整設備的可升降地腳螺栓來調整設備的水平度直到設備水平而穩固。然后按圖接線并可靠接地，把氣源接入機器所配帶的氣源接口，確保無漏氣現象。
4. Firstly, we can adjust the levelness of the equipment by adjusting the adjustable anchor bolts based on the actual situation of ground flatness until the equipment is level and stable. Then connect the wires according to the diagram and ground them reliably, connect the air source to the air source interface provided by the machine, and ensure that there is no air leakage.
5、向油槽中加注液壓油至指定位置。
5. Add hydraulic oil to the oil tank to the specified position.
6、接通電源并打開查看設備是否能夠正常運行。
6. Turn on the power and check if the device is functioning properly.
本文由 雙組份打膠機 為您精心提供，如想了解更多請點擊我們的網站： http://www.lingmaicnc.com，我們將會以最大的熱情為您解答!
This article is carefully provided by a two-component gluing machine. If you want to learn more, please click on our website: http://www.lingmaicnc.com We will answer you with the greatest enthusiasm!
- 丁基膠涂布機液壓油的選擇指南 2025/10/31
- 玻璃涂布機設備操作流程 2025/10/30
- 雙組份打膠機比例怎么調 2025/10/29
- 全自動鋁條折彎機折彎角度偏差的解決方法 2025/10/29
- 中空玻璃丁基膠涂布機漏油怎么解決 2025/10/28
- 臥式丁基膠涂布機糾偏原理 2025/10/27
- 立式丁基膠涂布機故障維修 2025/10/25
- 全自動丁基膠涂布機怎么換膠 2025/10/24
- 丁基膠涂布機液壓系統油路原理 2025/10/23
- 全自動中空玻璃封膠線的設備特點 2025/10/22
產品分類Product categories
聯系我們Contact us
- 咨詢熱線：0531-85717458 13705446998
- 公司地址： 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們：
